Superda electrical box roll forming machine production line for making distribution board, recessed metal board, electrical panel board, control panels, embedded metal cabinet equipment.
Wall mount electrical metal box & distribution board enclosure projector solution
Product specifications: height adjustable 300-1200mm, depth adjustable 150-400mm.
Electrical enclosure Production machine technical parameters
cold-roll strip,galvanized steel strip
1.0-1.5mm（base on 1.5mm design, when T.1mm effect alittle not good as 1.5mm）
L≤1000mm，Bend no more than 1mm；Deflection no more than 2mm
As per design
Electrical distribution board roll forming machine production line process
Uncoiler→ Straightening→Servo feeder→Hydraulic device→ Guide device → Roll forming machine →Bending device
Distribution box production line technology explaination
This production line is equipment for production of distribution boxes. The strip coil to be processed is manually placed on the uncoiler, and then corrected and tensioned. After leveling, it enters the hydraulic pre-punching and punching notch, and is sent to the forming machine by the guide device to form. Under the frictional damping action of the forming roller and pressure roller, after entering the bending part at a linear speed of 0-13m, the box is cut and bent as required, and then manually packed away. This production line produces 2-3 enclosures per minute. the production box quantity speed according to different product specifications.
Electric box production line main technical parameters
1.Details of accessory brand
Programmable controller (PLC)
Low-voltage circuit breaker
Hydraulic Solenoid Valve
Shun Xin, Taiwan
a. Applicable materials: cold rolled coil, galvanized coil
b. Material quality: Domestic GB standard
c. Tensile strength: δb≤780Mpa (Max.)
d. Yield strength: δs≤510Mpa (Max.)
e. Material thickness: 1.0-1.5mm
f. Material width: 200-450mm (Max.)
g. Inner diameter of steel coil: Φ360mm-Φ510mm
h. Outside diameter of steel coil: Φ1250 （Max.）
i. Steel coil weight: 3 t (Max.)
a. Number of forming staion: 16 sets of roller
b. Spindle specification: Ø48mm 40Gr quenching and tempering
c. Roller material: Gr12 mold steel heat treatment
d. Integral archway: precision machined from 25mm steel plate, the hole distance error is less than 0.1mm
e. Base plate thickness: 20mm
4, forming ability
a. Outside diameter of coil: Φ1250mm (Max.)
b. Material forming thickness: 1.0-1.5mm
c. Product width 160mm-400mm adjustable
5.Speed parameters of forming unit
a. Linear speed 0-13m / min
b. Acceleration time ＜ 30 seconds
6, Forming accuracy
a. Shear length tolerance: ≤ ± 0.5mm / m
b. Width tolerance: ≤ ± 0.5mm
c. Sickle curve: ≤2mm / m
d. Burr: ≤0.1mm (new blade cutting ordinary carbon steel plate with reasonable clearance)
e. Height tolerance: ≤ ± 0.5mm
The above tolerances are based on the first-grade steel coils with flat and edgeless waves.
7.Other equipment parameters
a. Power supply: 380V / 50HZ / 3PH (Or Custmized)
b. Installed capacity: about 32Kw
c. Forming speed: 0-13m / min
d. Cutting method: forming then cutting
e. Driving motor:
Straightener machine motor 2.2KW
Hydraulic punching 15kw,bending and cutting 5.5KW
Forming host motor 7.5KW
Servo motor 2KW
f. Floor area (approximately): length 30m × width 3m
(Roll Forming 7mX1.5m)
g. Production line direction: from left to right
(facing the unit from the operation table).
h. Equipment color: (Customer choice)
i. Unit equipment design can meet 12 hours of continuous production
j. Operating environment:
1: power supply voltage: 380V ± 10% / three-phase four-wire, frequency: 50HZ total power: about 32KW
2: Ambient temperature: 0-40 ° C, relative humidity: 60-95% RH.
Power distribution box production line devices：
2kw Mitsubishi motor
Servo Hydraulic machine
Hydraulic bending cutting
Guarantee of Quality
Superda guarantee bank steel enclosure & wall mounted electric distribution box roll forming line design accordance with clients required drawing, machine is brand new. Specification and performance as stipulated in drawing and operation with good smooth.
Automatic metal enclosure roll forming machine advantage
1, High efficiency production line, one minute can producing 2-3pcs
2, PLC control system, automatically and easy handle.
3, Gcr15 roller with quench process, hardness reach HRC60-65 ℃.
4,Tracking cutting system with Cr12 Cutting blade.
Different control panel dimensions are available.
Tel: +86 755 2824 6186
Mob: +86 188 1435 5377
Fax: +86 755 2883 9980
WhatsApp: +86 188 1435 5377